Installation

Check out the video below. HTC shown here, but coupe is similar (and easier since it is a few less steps)

 

https://youtu.be/rhCZ8IKWnL4

 

Installation Instructions:

Coupe:

(Optional) Fuel Line Relocation

Only do this step if you are finding it too difficult to install your covers, or if you want a little more clearance.

• Slide O2 sensor out of the way
• Remove the forward fuel line bolt on the passenger side (10mm)
• Install stud into insert that the bolt was removed from
• Re-install fuel line P-clamp bracket
• Install nut (10mm)
• Re-install O2 sensor into place by sliding it forward on the clip

• Remove aft fuel line stud bolt (10mm)
• Move fuel line P-clamp aside
• Re-install aft fuel line stud bolt (10mm)
• Install fuel line P-clamp onto stud
• Install nut (10mm)

Covers Installation

• If you purchased the screen, place it on top of the middle throttlebodies
• There are alignment notches in the screen that correspond to tabs on the plenums where the TB's bolt into them- 1 on each side
• The part of the screen that has a rubber edge trim goes toward the name plate
• Remove the name plate (2)  8mm bolts
• Install each cover over the plenums and install the 7mm bolt in the front and the 8mm bolt in the back. Leave these bolts loose at this stage.
• If you have the screen, ensure the corresponding edges seat into the notches on the sides of the screen
• Re-install the name plate re-using the factory bolts
• Only install bolts half way and keep loose at this point
• You can now tighten the bolts holding the covers on. Do not over-tighten these, they do not need to be cranked down super tight. Just make sure they are snug.
• You can use some loctite if you are concerned about them coming loose.
• Position the name plate to be centered in cutouts then tighten name plate bolts

 

 

HTC:

(Optional) Fuel Line Relocation

Only do this step if you are finding it too difficult to install your covers, or if you want a little more clearance.

• Slide O2 sensor out of the way
• Remove the forward fuel line bolt on the passenger side (10mm)
• Install stud into insert that the bolt was removed from
• Re-install fuel line P-clamp bracket
• Install nut (10mm)
• Re-install O2 sensor into place by sliding it forward on the clip

• Remove aft fuel line stud nut (10mm)
• Move aside coolant line bracket
• Remove aft fuel line stud bolt (10mm)
• Move fuel line P-clamp aside
• Re-install aft fuel line stud bolt (10mm)
• Install fuel line P-clamp onto stud
• Re-install coolant line bracket
• Install nut (10mm)

Covers Installation

• Put the top in service mode
• Remove the engine bay cover (T15)
• Install rubber cap onto nut insert above driver side intake manifold plenum
• If you purchased the screen, place it on top of the middle throttlebodies
• There are alignment notches in the screen that correspond to tabs on the plenums where the TB's bolt into them- 1 on each side
• The part of the screen that has a rubber edge trim goes toward the name plate
• Remove the 10mm bolt on the passenger side of the coolant reservoir
• Maneuver the coolant tank out of the way as required in the following steps
• No need to disconnect any coolant lines.
• Remove the coolant reservoir bracket on the driver side- 10mm bolt
• Remove the name plate (2)  8mm bolts
• Install each cover over the plenums and install the 7mm bolt in the front and the 8mm bolt in the back. Leave these bolts loose at this stage.
• If you have the screen, ensure the corresponding edges seat into the notches on the sides of the screen
• Re-install the name plate re-using the factory bolts
• Only install bolts half way and keep loose at this point
• You can now tighten the bolts holding the covers on. Do not over-tighten these, they do not need to be cranked down super tight. Just make sure they are snug.
• You can use some loctite if you are concerned about them coming loose.
• Position the name plate to be centered in cutouts then tighten name plate bolts
• Re-install the driver side coolant tank bracket (10mm bolt)
• Re-install the coolant tank (10mm bolt)
• Re-install the engine bay cover
• Take top out of service mode